EZ Chill Refrigerant, R-134a

18 oz (1 lb 2 oz) 510 g


 

Directions

Instructions: Always wear protective gloves and glasses. 1. Open Hood and Find Low-Pressure A/C Service Point: With engine off, open hood and locate the low pressure A/C service port (on the larger-diameter tubing between the compressor and evaporator). Remove the plastic cap from port and save. Tip: Visit rechargeac.com for additional help in locating your low-pressure service port. Note: For best results, charge under shade. Keep the car doors open while charging (front and back). Start car and turn on A/C. Set fan to highest setting and temperature to coldest setting. Make sure recirculation mode is selected. Attach quick-connect fitting on end of recharge hose to low-pressure service port identified earlier by pushing the connector ring back as the fitting is pushed on Note: Our quick-connect fitting will attach only onto the low-pressure port 2. Read Pressure Color: Without pushing the button, look at the gauge to see what color section the needle is pointing toward. Depending on the color, determine next step according to grid below: Colored Section of Gauge: Low; What it Means: System low on refrigerant. Continue to step 3 to begin recharging process. Colored Section of Gauge: Filled; What it Means: If needle is within the green section, system is properly charged and to additional refrigerant is needed. Malfunctioning A/C when needle within green indicates other system problems besides low refrigerant. Colored Section of Gauge: Yellow; What it Means: No additional refrigerant is needed. Colored Section of Gauge: See Instructions; What it Means: Confirm compressor clutch is engaged when checking pressure. If compressor is not engaged, ensure car is running and A/C is turned on. If needle is in the red and compressor is cycling on, do not add refrigerant. System needs to be serviced by technician. Other system problems besides low refrigerant may exist. The system needs to be serviced by a certified technician. 3. Charge System: Disconnect the gauge assembly from service port. Unscrew and remove plastic spacer between gauge assembly and can. Shake can well and screw can onto gauge assembly. Connect the quick-connect back on the low-side port. Make sure to always hold the can upright (12 o'clock position) before starting to charge. Squeeze the button to charge the A/C system. While charging shake the can up and down, alternating between an upright and sideways position. Every 15 seconds release button. After needle is stabilized, check pressure readings on gauge. Tip: Read pressure when gauge assembly is released, not while being squeezed. It is typical for gauge to bounce Around as the compressor is cycling. If that happens, read the lowest pressure. Stop charging when needle in green. Be careful not to overcharge your system. Do not let needle make it into the red area. Once needle makes it anywhere in green zone of the gauge, charging is complete. Do not try to get it to the highest part of the green zone or you risk overcharging. Remove hose from service port and replace plastic cap when finished. Store any unused refrigerant in a cool, dry place, with charging hose securely attached to can.

 

Product Details

Restores lost refrigerant. Stops leaks hoses, O-rings & gaskets. EZ Chill Refrigerant 134a. Restores Refrigerant- R-134a with A/C performance booster and oil restores lost refrigerant and lubricates system. Seals A/C Leaks - Safely seals common A/C leaks in rubber O-rings, gaskets and hoses. Includes Charging Hose with Gauge - Push-button dispenser and in-line gauge provide fast, easy and accurate recharging. Note: Hose and gauge can be reused for future system pressure checks with EZ Chill R-134a Refill cans. Contents: 15 oz. R-134a and 3 oz. of additives. Removable gauge assembly. Check refrigerant level any time. www.rechargeac.com. For tech support, call 1-888-318-5454, or visit www.RechargeAC.com. Emergency Tel +1314 985-1511. Made in China. Made in USA.

Nutrition Facts

Warnings

Warning: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.,First Aid: Eye Contact: Flush eyes with water for at least 15 minutes. Get medical attention if symptoms persist Skin Contact Flush with warm water. Get medical attention if irritation persists. Inhalation: Move to fresh air. Get medical attention if imitation or other symptoms develop. ,Warning! Contents under pressure. Eye and skin irritant. Carefully read precautions on rear panel. Warning: Keep out of reach of children. Exposure to skin may cause frostbite. Flush with warm water. If sprayed into eyes, flush with warm water. If inhaled, remove to fresh air and call physician immediately. Contains 1,1,1,2-tetrafluoroethane (811-97-2), Polyalkylene glycol monobutyl ether and proprietary elastomer. Do not store can in vehicle (may explode). Do not store above 120 degrees F or in direct sunlight. Keep can away from any source of electricity. Do not puncture or incinerate (burn) container. Exposure to skin may cause irritation and frostbite. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Always wear protective gloves and eyewear. Not for use in hybrid/electric vehicles with non-belt-driven (electric-driven) compressor.

Manufacturer

Energizer Auto, Inc.
St. Louis, MO

UPC

00048168021215