1. Home
  2. Screws
  3. TimberLOK FastenMaster. Wood Screws 50 ea BOX

TimberLOK FastenMaster. Wood Screws 50 ea BOX

On This Page

 

Directions

Installation Instructions: HeadLOK should be installed using an impact driver or high torque 1/2 inches variable speed drill (minimum 18V if cordless). Choose the proper length fastener so that the threads fully engage the main member (second piece). Bring the washer head flush to wood surface.

 

Description

Replaces 3/8 inches lag screws. 152 mm. No predrilling! Free spiderdrive bit code compliant. FastenMaster.LOKline. Meet code. Lower cost. HeadLOK is a heavy duty wood screw that is ideal for many wood-to-wood connections including decks, fences, headers, installing kitchen cabinets, kitchen islands and more. Guaranteed Corrosion Resistance: headLOK is guaranteed not to rust or corrode for the life of the project. The coating on this fastener has been tested in wood treatment chemicals, such as ACO, and found to provide equivalent protection to code approved hot-dipped galvanized coatings. HeadLOK is not recommended for use in saltwater applications (within 1,000 ft). Comparative Data: The statement Replaces 3/8 inches lags refers to the comparison of lateral (shear) design values for the HeadLOK as shown in our evaluation report and lag screw values as published in the current National Design Specification for Wood Construction (NDS). See table. For critical applications, a Professional Engineer (PE) may be consulted to determine proper connection design including the number and location of fasteners to meet local code and specific load requirements. Complete design values and engineering data in our evaluation report, ICC-ES ESR-1078, available at www.fastenmaster.com. Lateral Design Values (Z) for single shear connections loaded perpendicular to Grain Wood. S. Pine, D. Fir, SCL (Structural composite lumber (LVL, PSL and LSL); Specific Gravity (Wood species indentified typically have average specific gravity similar to the values shown on this table). 0.50; headlok 2-7/8 inches. 210; headLOK 4-1/2 inches +. 260; Lag screws. 3/8 inches. 130; Lag screws. 1/4 inches. 110; Common nail 20d. 170; Common nail 16d. 141; Wood. D. Fir-South; Specific Gravity (Wood species indentified typically have average specific gravity similar to the values shown on this table): 0.46; Headlok 2-7/8 inches. 180; headlok 4-1/2 inches + 240; Lag screws 3/8 inches. 120; Lag screws 1/4 inches. 100; Common nail 20d. 157; Common nail 16d. 131; Wood. Spruce pine fir; Specific Gravity (Wood species indentified typically have average specific gravity similar to the values shown on this table): 0.42; headLOK 2-7/8 inches. 150; headLOK 4-1/2 inches. 220; Lag Screws 3/8 inches. 110; Lag Screws 1/4 inches. 100; Common Nail 20d. 144; Common Nail 16d. 120; Wood. Min. Penetration into main member: headLOK 1-3/8 inches; headLOK 3 inches; Lag screws 3 inches; Lag screws 2 inches; Common Nail. 2 inches; Common nail.1-5/8 inches. Design values based on 1-1/2 inches side member thickness and penetration in main member as shown. For thinner materials, refer to the NDS or ICC report for appropriate adjustment. These values may be subject to adjustment factors (Section 10.3 in NDS) based on conditions during installation or expected during service life. Compliance audited by ICC-ES. 6 Inches HeadLOK head marking.

Other Description

Smartlabel: View a headLOK Intstallation video. For additional information or technical assistance, please contact Fastenmaster Technical Support at 800-518-3569.

Warnings

Not Applicable

UPC

00608309410591