Smiths Sharpener 1 ea BLISTER PACK
On This Page
Directions
Care & Storage: Always clean your sharpener after use. Clean with a damp cloth or mild brush. Do not rinse with water. Store in a dry place. Knife Sharpening Instructions: Note: These instructions only apply to straight edge knives with a flat grind on both sides of the blade. This sharpener is not intended for use in sharpening serrated edge blades or blades with a flat grind on just one side of the blade. A reasonably sharp blade may only require light honing in the fine ceramic slot. The coarse carbide blades in the head of the sharpener are intended for very dull of damaged edges that require a new sharp edge to be put on the blade or for initial edge setting the first time you sharpen your knife with this sharpener. Very Dull or Damaged Blades: 1. Place your knife on a flat surface with the cutting edge facing up and allow about 1 inch of the blade to extend past the edge of the surface. Secure the knife with downward pressure on the handle. 2. Place the sharpening slot in the head of the sharpener over the cutting edge at an approximate 45 degree angle to the blade near the handle of your knife. 3. Pull sharpener over cutting edge from heel to tip while applying moderate, downward pressure. Use a smooth, consistent stroke when pulling the sharpener over the cutting edge and continue your outward motion at the end of each stroke to avoid any contact with the blade. If your blade curves out to the tip, be sure to follow the curvature of the blade all the way out to the tip to ensure sharpening of the complete cutting edge. 4. Repeat a minimum of 5 pulls. After 5 pulls, the sharpener should begin to glide smoothly over the cutting edge. If not, additional pulls are required. Note: Knives made of extremely hard steel may require in excess of 20 pulls to properly set the edge for finishing. 5. Move to the find ceramic slot for final edge honing. See instructions below. Replaceable Carbide Blades – when the carbide blades in the head of the sharpener stop removing metal from the knife blade, they should be replaced. Contact Smith's for replacement blades. Reasonably Sharp Blades – Light Honing: Place the sharpener on a flat surface as shown and grip the handle for stability. Hold the knife comfortably in your other hand. 2. Insert knife blade fully into the sharpening slot with cutting edge of the blade resting at the bottom of the V-shaped slot and the knife straight up and down. Tilt the tip of the blade down slightly. 3. While applying light, downward pressure, pull the knife blade through the sharpening slot from heel to tip. If your blade curves up at the end, be sure to lift the handle of the knife as you approach the curved portion of the blade to sharpen all the way out to the tip of the blade. 4. Repeat a minimum of 6-8 pulls always sharpening from heel to tip (never back and forth). Note: Knives made of extremely hard steel may require additional pulls. 5. Check the sharpness of your blade. If additional sharpening is needed, repeat process until sharp. Scissors/Game Shears Sharpening Instructions: 1. With your free hand, hold the head of the sharpener as shown and place the base of the sharpener on a flat surface. Note: If you are sharpening right-handed scissors/shears, the words right handed should be facing you. Opposite or left-handed. 2. Open your scissors or game shears and insert just the tips of the blades just far enough into the slot to be able to clamp down on the square rod. 3. Close scissors/shears on the sharpening rod as if you were trying to cut the rod, then push the scissors/shears through the slot while trying to keep the blades closed. Note: Scissors or game shears made of extremely hard steel may require additional pushes through the slot when sharpening their blades. Spanish instructions inside card.
Description
Since 1886. Sharpens knives, scissors, and shears; easy grip handle; attaches to belt or backpack. Premium abrasives for a sharper cutting edge.Warnings
Always keep your fingers inside the hand guard and your thumb securely on the thumb rest indention on the top of the sharpener or possible injury may occur. Always rest your sharpener on a sturdy, flat surface during scissors sharpening.UPC
00027925501856