Krylon Flurorescent, Specialty
11 oz (311 g)
On This Page
Directions
For boldest fluorescent color, use a white base coat; flows under ultraviolent (black) light. Materials: Wood, metal, glass & paper. Painting Conditions: Spray outdoors or in a well ventilated area. Protect surrounding areas. Best results when temperature is 55 degrees F (12 degrees C) to 75 degrees F (24 degrees C) and humidity is below 60%. Note: Applying outside of this range may impact finish. Painting: Shake until ball inside begins to rattle, then shake for an additional 2 minutes. Test an inconspicuous are first. Hold can 10 cm - 12 cm from surface, spray in sweeping motion from side to side with slight overlap. Apply multiple thin coats to avoid runs and drips. Dry & Application Times: Driesto touch in 15 minutes or less. Handle after 2 hours. Apply additional coats within 2 hours or after 48 hours. After Use: If spray button becomes clogged, wear eye protection, wipe off the button opening with lacquer thinner, following solvent manufacturer's instruction - Do not stick pin in spray button opening. Clean overspray with paint or lacquer thinner, following solvent manufacturer's instructions. Wash hands after using.
Product Details
No runs, no drips, no errors. Bold neon for high visibility. Ultra-brilliant color. Interior/exterior. For home & commercial use. Dries in 15 minutes. Less effort. Spray anywhere. Satisfaction Guaranteed: If dissatisfied contact us with product number and batch code on bottom of can for full purchase price refund. Conforms to the health requirements of ASTM D-4236. www.krylon.com. Please recycle when empty. Recycling facilities for this product may not exist in your area. Made in the USA with global materials.Nutrition Facts
Warnings
First Aid: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. ,Danger! Extremely flammable - Vapors may cause flash fires! Contents under pressure. Vapor harmful. Irritates eyes, skin and respiratory tract. See other cautions on back panel. Preparation: Warning! If you scrape, sand or remove old paint, you may release lead dust. Lead is toxic. Contact the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. Surfaces should be clean, dull and dry. Remove loose paint, rust, dirt, grease and oil. To improve adhesion, sand glossy or rough surfaces until smooth. Cautions: Contains Acetone, Propane, N-Butyl Acetate, Butane, Aliphatic Hydrocarbon, Ethyl 3-Ethoxypropionate And Xylene. Danger! Extremely flammable. Keep away from heat, sparks and open flame. Vapors will accumulate readily and may ignite explosively. Keep area ventilated and until all vapors are gone. Do not smoke - Extinguish all flames, pilot lights and heaters. Turn off stoves, electric tools and appliances, and any other source of ignition. Contents under pressure. Avoid prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may cause bursting. Do not puncture, incinerate, burn or store above 120 degrees F. Keep upright in a cool, dry place. Do not discard empty can in trash compactor. Vapor Harmful. Use with adequate ventilation. Avoid continuous breathing of vapor and spray mist. To an vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Delayed effect from Long term overexposure. Contains solvents which can cause permanent brain and nervous system damage, Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. Do not take internally. Keep out of the reach of children. Contact a physician for more health information. Danger: Rags, steel, wool, other waste soaked with this product and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked there with this product and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.Manufacturer
Krylon Products Group
Cleveland, OH 44115
UPC
00724504068853